74 products
bags-1.1
Aseptic sampling bag
50 ml–1 L; bag body, inlet/outlet lines and sampling line; multi-branch or single-branch; gamma irradiation (25–40 kGy); endotoxin < 0.25 EU/ml; steri…
bags-1.10
WAVE Reaction Bag
Applications: cell culture, antibodies, vaccines, cell therapy, gene therapy and more; ready-to-use and disposable — no cleaning required; high physic…
bags-1.11
The PUPSIT system
Single-use sterilising filtration line, configurable as redundant or serial filtration; one to multiple pressure monitoring ports (mechanical diaphrag…
bags-1.12
Freeze storage bag
Advanced gamma-stable fluoropolymer construction with broad chemical compatibility; temperature range −196 °C to 121 °C; monolayer technology — no adh…
bags-1.2
Multi sterile sampling bag
Needle-free sampling valve design; number of sampling ports freely customised to the sampling regimen; choice of three disconnection methods — aseptic…
bags-1.3
Sampler / Silicone stopper / Disconnect pliers accessories
Two-port sampler: 316L stainless steel base, medical-grade silicone rubber seal, A6061 aluminium alloy needle slot, 316L stainless steel threaded cap.…
bags-1.4
2D liquid storage bag
Multi-layer co-extruded film; volume 50 ml–50 L; bag body, inlet/outlet lines and sampling line etc.; gamma irradiation (25–40 kGy); endotoxin < 0.25 …
bags-1.5
3D liquid storage bag
Multi-layer co-extruded film; volume 100 L–3000 L; gamma irradiation (25–40 kGy); endotoxin < 0.25 EU/ml; sterility assurance level 10⁻⁶ SAL; insolubl…
bags-1.6
2D liquid preparation bag
Suitable for uniform mixing and stirring of liquid–liquid and solid–liquid systems; modular design, with impeller type, bag and support vessel selecta…
bags-1.7
3D magnetic stirring bag
Multi-layer co-extruded film, stirring impeller, powder inlet, inlet/outlet lines, temperature probe port; impeller mounted inside the bag bottom with…
bags-1.8
Filling bag
2D single-use aseptic filling bag comprising a high-level buffer bag, filling line and filling needle. Six key advantages: pre-sterilised — no autocla…
bags-1.9
Feeding bag
Soft funnel-shaped design for easy transfer and handling of solid powders; supplied with powder inlet, gasket, clamp, blind plate and sealing clip; su…
cleanroom-4.1
Sterile pen
Cleanroom-packaged, each pen double-bagged with 10 pens in a third outer bag; specially formulated oil-based ink for comfortable writing and low visco…
cleanroom-4.10
Tyvek clean respirator bag — Sheet-shaped
DuPont uncoated Tyvek 1073B base paper + pharmaceutical-grade HDPE film
cleanroom-4.11
Cleanroom notebook
Heat- and moisture-resistant, smooth writing, low particle generation; professional cleanroom paper significantly reduces dust generated by writing an…
cleanroom-4.12
Cleanroom printing paper
Low particle generation, fine paper texture, smooth writing; designed specifically for controlled environments such as cleanrooms and laboratories; wa…
cleanroom-4.3
Dust free wiping cloth — Composite ultra-fine dust-free cloth
Orange-slice bicomponent polyester–nylon ultra-fine fibre with continuous interlocking weave; superior absorbency and particulate capture, excellent c…
1:1 product image · replaceable later
cleanroom-4.4
Dust free wiping cloth — Polyester dust-free cloth
Single-layer 100% continuous polyester fibre weave; chemical resistance, high strength, high abrasion resistance, high liquid absorbency; low particle…
cleanroom-4.6
Sterilized breathing bag — Roll type
Material: medical-grade imported 60 g medical dialysis paper + reinforced high-temperature composite film
cleanroom-4.7
Sterilized breathing bag — Three-dimensional rolled
Material: medical-grade imported 60 g medical dialysis paper + reinforced high-temperature composite film
cleanroom-4.8
Sterilized breathing bag — Self-sealing sheet type
Material: medical-grade imported 60 g medical dialysis paper + reinforced high-temperature composite film
cleanroom-4.9
Tyvek clean respirator bag — Roll-pack
DuPont uncoated Tyvek 1073B base paper + pharmaceutical-grade HDPE film. Features: high cleanliness (produced in a Class 100 cleanroom, safe and relia…
consumables-3.1
Aseptic disconnect ring
Enables aseptic disconnection of silicone, thermoplastic and other flexible tubing; used with manual or electric aseptic disconnect pliers
consumables-3.11
CPC connector
Aseptic connection technology, open-connection technology and aseptic disconnection technology
consumables-3.12
Stainless steel joint
Custom stainless steel connectors available, including sanitary quick-connect barbed, T-type and Y-type connectors
consumables-3.13
Interception clamp / Pinch valve
Enables easy and safe flow shut-off, suited to the frequent flow-interruption demands of biopharmaceutical processes; easy to install, simple to open …
consumables-3.14
Robert's clip
Clamps the tubing to shut off flow; copolymer polyoxymethylene or PBT material combining rigidity with long service life; five adjustment positions to…
consumables-3.15
Mixing paddle
Small mixing paddles S1/S2, medium mixing paddle M1, large mixing paddle L1
consumables-3.16
PP storage tank
Barrel body with screw cap and TPE gasket, autoclavable prior to use; for autoclave sterilisation of pharmaceutical raw materials or media, bulk stora…
consumables-3.17
Tank cap / Three-way cap
Three-way cap and standard cap; fit NEWMEEN vacuum bottles and large barrels
consumables-3.18
Silicone tube / Peristaltic pump tube
Flexible tubing for bioprocess fluid transfer
consumables-3.2
Plastic joint — Straight connector
Fits silicone tubing with internal diameter 1/16"–1/2"
consumables-3.21
GFF Series - Fiberglass Folding Filter Cartridge
Ultra-fine glass fibre depth filter cartridge with efficiency above 96%; suitable for feed streams containing colloids, oils and high particulate load…
consumables-3.4
Plastic joint — Cross connector
Fits silicone tubing with internal diameter 1/16", 3/32", 1/8" and 1/4"
consumables-3.5
Plastic joint — Y-type connector
Fits silicone tubing with internal diameter 3/32"–3/8"
consumables-3.6
Plastic joint — T-type connector
Fits silicone tubing with internal diameter 1/16"–1/4"
consumables-3.7
Plastic joint — Luer connector
Female Luer and male Luer connectors; fit silicone tubing with internal diameter 1/16"–1/4"
consumables-3.8
Plastic joint — Plug / Luer plug / Needleless sampling valve
Plugs fit silicone tubing with internal diameter 1/8"–1/2"; needleless sampling valve with protective cap, fits female Luer connectors
consumables-3.9
Plastic joint — TC connector / Blind plate
TC25 and TC50 connectors fit silicone tubing with internal diameter 1/4"–3/4"; TC blind plates fit sanitary clamp ferrules
consumables-3.22
7-layer co-extruded film, BS-1958
7-layer structure (inside to outside): ULDPE 100 µm (heat-sealing layer) / LLDPE 100 µm / adhesive polyolefin 20 µm / EVOH barrier 25 µm / adhesive po…
consumables-3.23
7-layer co-extruded film, BS-1955-03
7-layer structure (inside to outside): ULDPE 100 µm (heat-sealing layer) / LLDPE 100 µm / adhesive polyolefin 20 µm / barrier layer 15 µm / barrier la…
equipment-2.1
Liquid preparation system — Mobile magnetic stirring system
30/50/100/200/300/500/1000 L; frame and support vessel in brushed 304 stainless steel; magnetic motor drive — no mechanical seal, no stirring shaft pe…
equipment-2.10
Single-Use Pressure Sensor — B Series
Female Luer both ends; PP material; 60 psi range; sterilisable by irradiation or 121 °C moist heat; note: accuracy is unaffected at low doses, while a…
equipment-2.11
Data transmission cable
For data transmission and connection between pressure monitoring recorders or transmitters and sensors; supports both in-house device-to-in-house sens…
equipment-2.12
Hollow fiber TTF system — Prototype/Lab scale
Applications across pharmaceutical, fermentation and food industries: desalting and concentration of enzyme and protein solutions; purification of pha…
equipment-2.13
Hollow fiber TTF system — Pilot scale
Suitable for pilot-scale bioprocess trials and small-scale production; split design separating the circulation tank from the ultrafiltration section; …
equipment-2.14
Hollow fiber TTF system — Production scale
Production-scale automated ultrafiltration system with a high degree of automation, intended for industrial-scale production; applied to the separatio…
equipment-2.15
Stainless steel filter
Stainless steel microporous pleated filter with SUS316L or SUS304 housing; filters liquids (particles above 0.1 μm) and gases (above 0.01 μm); high fi…
equipment-2.16
Filter Integrity Tester Version 1.0
Tests filters of all types including membrane disc, capsule and cartridge formats; minimum detectable membrane disc Φ20 mm, maximum testable 5-cartrid…
equipment-2.17
Filter Integrity Tester Version 2.0
Precision instrument designed specifically for integrity testing of all types of filter cartridges; widely used in pharmaceutical, biotechnology, food…
equipment-2.18
Bag integrity tester
Pressure decay test method; supports manual entry and selection of different bag specifications; branded vacuum pneumatic control components; four-lev…
equipment-2.19
Wall-penetrating system
Single-use cross-grade wall-penetrating system that achieves aseptic transfer of multi-line fluids through a stainless steel channel and pre-sterilise…
equipment-2.2
Liquid preparation system — Desktop magnetic stirring system
Stirring of small volumes from 5–20 L, offering greater precision and a higher degree of integration; stirring speed 0–600 rpm; weighing accuracy C3 (…
equipment-2.20
Electric sterile disconnect pliers
Dimensions 390 × 110 × 80 mm, 3.3 kg; supplied as standard with 2 rechargeable batteries, 1 charger and 2 blade sizes; small blade fits tubing with ou…
equipment-2.3
Liquid preparation system — Magnetic levitation stirring system
Composed of two main modules — stirring mechanism and control system; a single control system can drive two stirring units in tandem; integrates stirr…
equipment-2.4
Multi-layer Liquid Storage Trolley
50 L three-, four- and five-tier liquid storage trolleys; 100 L three-, four- and five-tier liquid storage trolleys; specific configuration customised…
equipment-2.5
WAVE Bioreactor
10 L / 25 L / 50 L rocking bioreactor system; rocking angle ±15°; weighing accuracy 1% (using a well-known weighing brand); temperature control accura…
equipment-2.6
Pressure monitoring system — Portable pressure monitoring recorder
WYPMR-H01: compact and highly portable; million-record data storage; CSV output; 1–3 channel pressure acquisition with differential pressure display; …
equipment-2.7
Pressure monitoring system — Pressure monitoring recorder
WYPMR-V02: colour touchscreen, audible alarm, USB data export; multi-level user privileges, audit trail, intelligent threshold alarms and line-break a…
equipment-2.8
Pressure Transmitter WPT-101
Developed in-house by NEWMEEN; acquires data from three single-use pressure sensors simultaneously and transmits via 4–20 mA current or RS485; measuri…
equipment-2.9
Single-Use Pressure Sensor — A Series
Medical-grade resistive type; connector dust- and water-proof to IP67; pressure range −6 PSI to 60 PSI; accuracy: ±2% of reading (−6 to 0 PSI), ±2% (0…
equipment-2.21
500 L single-use bioreactor
500 L nominal working volume; single-use bag in a 316L stainless steel support tank; skid-mounted frame with an independent control cabinet; top-entry…
equipment-2.22
Glass bioreactor, 1.5–15 L
Single-layer borosilicate glass; 1.5 / 3.0 / 5.0 / 6.0 / 7.5 / 10.0 / 13.0 / 15.0 L; single, 2-, 4-, 6-unit and larger configurations; 0–1300 rpm; 5–6…
equipment-2.23
Stainless steel fermenter, 10–1000 L
Volumes: 10/20/30/50 L (lab), 100/200/300/500 L (pilot), 1000 L (production); 316L vessel with 304 jacket; mechanical agitation at 10–1000 rpm ±2 (lab…
equipment-2.24
Parallel bioreactor system, 0.5–1.5 L
Single-layer borosilicate glass; 0.5 / 0.8 / 1.0 / 1.3 / 1.5 L; single, 2-, 4-, 6-, 8-unit and larger configurations; 0–1300 rpm; 5–65 °C ±0.1 °C with…
equipment-2.25
Aseptic tube welder
Tubing sizes 1/8"×1/4", 1/4"×7/16", 3/8"×5/8", 1/2"×3/4" (4 adaptor sets included, up to 12 supported, custom adaptors available); compatible with C-F…
equipment-2.26
Aseptic tube sealer
Tubing OD 1/4"–1.0" (6.35–25.4 mm); type I up to 7/8", type II up to 1.0"; wall thickness 1/16"–1/8" (1.6–3.2 mm); compatible with C-FLEX, PharMed BPT…
equipment-2.27
αβ split butterfly valve
Metal-to-metal seat sealing; 316L stainless steel body; FKM seal compliant with FDA; OEL ≤0.1 µg/m³, OEB ≥5; pressure resistance ≥0.3 MPa with the pro…